Download program chevy transmitter car kit

Immolation mr. becker's classroom supplies. Remove the transmitter from the cupholder and press Unlock or Lock on the transmitter. To program additional transmitters, repeat Steps 4–6.When all additional transmitters are programmed, press and hold ENGINE START/STOP for 12 seconds to exit programming mode. How to Program a Chevy Garage Door Opener One useful feature many new Chevrolet models come equipped with today is the Chevy Homelink garage door opener. Willbrownblog. If your vehicle is equipped with this useful feature, you might be wondering how to program it to fully enjoy its convenience. You can program Chevrolet keyless entry remote-control key fobs from your car just like you can program the key fob remotes of a variety of other makes and models. These remotes can be synced to your transmitter from your driver's seat using only the remote itself and your ignition key. With the ability to program. Remove the transmitter from the transmitter pocket and press unlock or lock on the transmitter. To program additional transmitters, repeat Steps 4–6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode. The Chevrolet Malibu is among the many Chevy cars that come with remote and keyless entry. With this technology, you can control your car's door locks, your trunk and your panic alarm from as far as a couple hundred feet away in the street or in a parking lot.

I picked up a rollback/unwind 2016 Spark EV (875mi) a couple weeks ago, and it only came with 1 key :-/
Having only a single key is a recipe for disaster, so I promptly ordered PN 94543206 (my original key is 94543205..) and had it cut at a locksmith yesterday.
Anyhow, the manual for 2016 doesn't seem to exist, nor did I receive one with the car, so I looked up the manual for the 2015 and there were procedures within. They do not seem to work.
What I did:
0. car not plugged in to power

Download Program Chevy Transmitter Car Kit

1. approached car
2. unlock using remote
3. open flap on emergency key cover (ignition area)
4. insert existing key into ignition keyway
5. nearly immediately insert new key into driver side door keyway

Download Program Chevy Transmitter Manual

6. turn door key from middle position to unlock position (counter-clockwise) 5 times at moderate speed (not trying to whip it from neutral to unlock quickly, though I did try at varying speeds) -- sometimes I tried more than 5 times, sometimes I tried faster, and sometimes slower
Transmitter

Download program chevy transmitter manual

7. wait for anything to show up on the DIC, only usual driver entry information is shown (charge status, plug in to charge, mi remaining, etc.)
8. DIC goes blank after a while (idle timeout), and I try to repeat this all again several times, to the same effect.
Download Program Chevy Transmitter

The DIC never says 'READY FOR REMOTE' etc. I cannot proceed beyond step 2 below.
I thought the 2016 was practically a newer 2015.. Has the procedure really changed, or did I do something wrong?
Verbatim from the 2015 manual:
Programming with a Recognized Transmitter
A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all of the transmitters, both currently recognized and new, must be with you.
1. Remove the rubber cap on the steering column. Press the button on the recognized transmitter to extend the key blade. Insert the key blade into the transmitter slot.
2. Insert the vehicle key of the new transmitter into the lock cylinder on the outside of the driver door and turn the key to the unlock position five times within 10 seconds.
The Driver Information Center (DIC) displays READY FOR REMOTE #2, 3, 4 or 5.
3. Remove the recognized key and place the new transmitter into the transmitter slot.
4. Press the POWER button. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter.
5. Remove the transmitter from the transmitter and press X (UNLOCK button)
To program additional transmitters, repeat Steps 3-5
When all additional transmitters are programmed, press and hold the POWER for 12 seconds to exit programming mode.
Replace the plastic trim piece from the small storage area.